Pevly

Author: Empire Flippers

  • 5 Best Tiko 3D Printer Review – Alternatives

    5 Best Tiko 3D Printer Review – Alternatives

    On March 30, 2015, a Kickstarter project was opened to create a revolutionary new 3D printer. One month later, in April 2015, the Kickstarter had raised $2,950,874 from 16,538 backers who put up at least $179 each. Shipping was estimated to start in November 2015, approximately seven months later. The printer was going to be known as the Tiko Unibody 3D Printer.

    The designers of this printer were visionaries in every sense of the word. The Tiko 3D printer what the creators of the term “state-of-the-art” had in mind when they coined the phrase. Here are some of the planned specifications.

    • The maximum print volume was supposed to be 138.3 cubic inches.
    • The shape of the print area wouldn’t have been the usual rectangle or circle. Instead, it would have been triangular but with rounded corners. The height would have been 4.9 inches. If you were printing something with a cylindrical shape, the diameter of that cylinder could have been as large as 4.9 inches.
    • The layer resolution was supposed to be 50 to 250 microns.
    • The printing zone would have been enclosed.
    • The print bed would have been made of a flexible plastic. That would have made it easy to pop off the printed item without damaging it.
    • Tiko would have been able to connect to Wi-Fi so that you could print from virtually anywhere, including a smartphone. If Wi-Fi was not available, you could have used the printer to create a wireless access point. This would have let you print directly from your computer to the printer.
    • If the unit was ever jarred or moved while printing, a built-in accelerometer would have sensed this and shut the Tiko down automatically.
    • The accelerometer would have also had a role in the automatic calibration process.

    This was your big chance to participate in the development of cutting-edge technology. For a mere $179, you could have contributed to a Kickstarter project and gotten a new type of 3D printer, one that would have made IT history.

    The first shipment (from Hong Kong) went out in December 2016. That was 13 months after the initial expected ship date. Those units, once they were set up by the new owners, had problems. By February 22, 2017, the project was over. The Tiko 3D printer became someone’s broken dream. There were subsequent efforts to revive the brand, but nothing came of them. In the end, the biggest problem was probably not the design or planning. It was probably that the project was underfunded and couldn’t survive the bad times.

    Even though their $179 investment was gone, those who contributed to the Tiko Kickstarter project were offered an inexpensive way to acquire a 3D printer. The CEO of M3D offered anyone who lost money on the Tiko Kickstarter the opportunity to purchase a Micro 3D Printer for a discounted price of $199. It was a good deal for anyone who accepted the offer and a smart way for M3D to expand its customer base.

    There are plenty of other options available for those who were hoping to purchase a Tiko 3D printer. We will list some of those alternatives for you. But first, here is some background information on 3D printers.

    [amazon box= “B07CJQ3D6L,B07DMZ1YQD,B07HDHHBRJ,B07MLWFXHF,B0757H1Q5K” template=”table”]

    3D Printer FAQs

    How Do 3D Printers Work?

    Where Can 3D Printers Be Purchased?

    How We Reviewed

    3d Printer at the top of the table

    Image by Karolina Grabowska from Pixabay

    ​The printers we reviewed were chosen based on price. We were looking for printers at a price close to the $179 that would have been spent on the Tiko. Quite a bit of time has passed since the beginning of the Tiko project. In that time, technology has marched on. It is reasonable to expect that since then, prices have dropped, and functionality has increased. It is interesting to see how some of the ideas in the Tiko design have made it into currently available printers.

    All the printers reviewed here are delivered completely assembled. There are many more available in this price range that require assembly. Some even come in the form of a kit, which sounds like an extreme form of assembly. If you are good with your hands, have a sense of adventure and have the patience of a saint, you might do well to find a kit. This will give you lot more printer for the money.

    Overall Price Range of This Product

    3D Printing using the 3D printer

    Image by Lutz Peter from Pixabay

    In general, the cost of filament-based 3D printers ranges from the low hundreds to many thousands of dollars. Because we are looking to replace a $179 Tiko printer, we have decided to limit our price range to between $150 and $350.

    5 Best Alternatives to the Failed Tiko 3D Printer

    Monoprice Mini Delta 3D Printer

    [amazon box=”B07CJQ3D6L”]

    Price

    $159

    Setup

    Assembled

    Interface

    Wi-Fi, USB, microSD

    Display

    LCD

    Technology

    FFF

    Print Area 

    4.3” x 4.3” x 4.7”

    Enclosed 

    No

    Heated Bed

    Yes

    Bed Leveling

    Auto

    Nozzle Size 

    .04 mm

    Extruders

    1

    Software Inc. 

    Cura, supports Windows XP or

    later, Mac OS X (10.6 64-bit)

    Resolution

    50 micron

    Dimensions

    14.2” x 10.4” x 16.9”

    Weight 

    30.6 lbs

    Includes

    USB cable, microSD card, power adapter, cord

    Where To Buy

    Monoprice, Amazon

    Warranty

    30-day money back guarantee, one year for repair of

    manufacturer’s defects

    This low-end printer has it all. It works right out of the box and, except for its lack of enclosure, it has all the great features of higher-end systems. Wi-Fi connectivity allows you to cut the leash to your computer. It only addresses smaller print projects, but if you can work with that limitation, this printer is for you. This model is also worth considering if you are looking to buy your first 3D printer.

    PROS

    • Wi-Fi interface
    • SD card
    • Excellent features at a low cost
    • Heated bed

    CONS

    • None

    M3D Micro+ Desktop 3D Printer

    [amazon box=”B07DMZ1YQD”]

    Price

    $349

    Setup

    Assembled

    Interface

    USB

    Display

    No

    Technology

    FFF

    Print Area 

    4.3” x 4.5” x 4.6”

    Enclosed 

    No

    Heated Bed

    No

    Bed Leveling

    Auto

    Nozzle Size 

    0.35 mm

    Extruders

    1

    Software Inc. 

    M3D

    Resolution

    50 to 350 microns

    Dimensions

    7.3” x 7.3” x 7.3”

    Weight 

    4.4 lbs

    Includes

    M3D software, USB cable, power adapter

    Where To Buy

    Amazon, M3D website

    Warranty

    Three months for manufacturer’s defects

    PROS

    • Lightweight

    CONS

    • No Display

    da Vinci Mini Wireless 3D Printer

    [amazon box=”B07HDHHBRJ”]

    Price

    $200

    Setup

    Assembled

    Interface

    USB, Wi-Fi

    Display

    No

    Technology

    FFF

    Print Area 

    5.9” x 5.9” x 5.9”      

    Enclosed 

    No

    Heated Bed

    No

    Bed Leveling

    Auto

    Nozzle Size 

    .04 mm

    Extruders

    1

    Software Inc. 

    XYZware, supports Windows 7 and above, Mac OSX 10.8 and

    above   

    Resolution

    100 microns

    Dimensions

    15.4” x 13.2” x 14.2”

    Weight 

    18 lbs

    Includes

    Starter filament

    Where To Buy

    XYZ Printing, Amazon

    Warranty

    Undetermined

    This is another excellent entry-level printer that works right out of the box. Wi-Fi connectivity is a big plus, as is that automatic bed-leveling feature. The resolution of 100 microns is good, but not great. It only runs filaments available from XYZ Printers. The proprietary XYZware software is provided.

    PROS

    • Wi-Fi interface

    CONS

    • Uses only XYZ Printing filaments
    • Resolution

    HopeWant Desktop 3D Printer

    [amazon box=”B07MLWFXHF”]

    This seems to be a good entry-level printer. Remove it from the shipping carton, and it’s ready to go. It prints either from the computer or the SD card (TF card).

    PROS

    • SD Card
    • Price

    CONS

    • No Display
    • Resolution

    Print-Rite CoLiDo Delta 3D Printer

    [amazon box=”B0757H1Q5K”]

    Price

    $269

    Setup

    Assembled

    Interface

    USB

    Display

    No

    Technology

    FDM

    Print Area 

    5” diameter x 5.9” high

    Enclosed 

    No

    Heated Bed

    No

    Bed Leveling

    No

    Nozzle Size 

    .04 mm

    Extruders

    1

    Software Inc. 

    Repetier-Host, supports Windows 7 and above, Mac

    Resolution

    50 microns

    Dimensions

    9.9” diameter x 17.5 high

    Weight 

    12 lbs

    Includes

    Flash drive, USB cable, adapter, filament

    Where To Buy

    Amazon, CoLiDo

    Warranty

    30-day return policy, one-year international warranty

    The price of this unit is at the high end of our range but, as always, you get what you pay for. This printer is different from the others in that it is configured for a circular print area. It is easy to set up, and it prints quickly due to its three-axis parallel movement system. This is an excellent printer for a beginner, but the quality and consistency are good enough for professional applications. At 30 watts, it is economical to operate.

    PROS

    • Fast printing
    • Low power

    CONS

    • No Display
    • Resolution

    Conclusion

    The Monoprice Mini Delta 3D printer was the clear winner here. For a printer with its features, the price is almost unbelievable. Wi-Fi connectivity and use of SD cards to store print files make it very user friendly. The heated bed also makes this the only printer on the list that could be comfortably used in a professional setting.

    Featured Image: Image by ZMorph3D from Pixabay

  • Robo 3D Printer Review: The High-Quality Prints

    Robo 3D Printer Review: The High-Quality Prints

    Robo 3D Printer Review

    Robo is an emerging manufacturer of consumer-level desktop 3D printers. The brand currently sells three printer models that are easy to set up and use to start creating. This review covers the features of the Robo R1+, C2, and R2 models to help consumers decide on the best Robo 3D printer for their budgets and design needs.

    What Are Robo 3D Printers?

    Robo is a 3D printer company based in San Diego, California that launched in 2012. The company crowdsourced funds to develop its first model, the Robo R1 3D printer. They now sell and provide support for three newer models, the R1+, C2, and R2. These printers enable users to produce designs created using computer-aided design software or templates.

    Robo’s easy-to-use, consumer-level printers are capable of printing with as many as 20 or 30 different types of filament and have features designed to improve the detail, resolution, and overall quality of each print job. All three of their current printer models feature high-temperature extruders, and two out of three models have heated print beds.

    Robo printers are desktop-sized and include most of the features that hobbyists look for in these devices. Rather than relying on complex and costly CAD software, Robo printer users can use open-source modeling software or the company’s free mobile applications to design and create objects.

    Robo 3D Printer Specifications

    Robo R1+

    The most affordable model in Robo’s current line of desktop 3D printers is the Robo R1+. This value-oriented model is larger than the C2 and R2 models and is capable of printing with more than 30 filaments, allowing for a wide range of creative possibilities. The R1+ is compatible with open-source design software and iOS and Mac OS, Linux, and Windows operating systems.

    The Robo R1+ has a large 10″ x 9″ x 8″ (254 x 228.6 x 203.2 mm) print size and the overall dimensions of the printer are 17.1″ x 18.1″ x 15.1″ (433.8 x 459.7 x 383.54 mm). This desktop model weighs 21 pounds (9.53 kg). The R1+ is capable of printing in the 50 to 300-micron layer resolution range with XYZ accuracy of 11, 11, and 1.6 microns. The quick-change nozzle print head has a diameter of 0.4mm, a travel speed of up to 80 mm/s, and a print speed of up to 50 mm/s. The nozzle temperature ranges from 240 degrees Celsius (464 degrees Fahrenheit) up to 290 degrees Celsius (554 degrees Fahrenheit) with an all-metal extruder.

    The metal hot ends on this fused filament fabrication device can emit materials ranging from ABS to a variety of types of PLA, PET-G (flex and sturdy), nylons, polycarbonate, and flexible TPE and TPU. This printer is capable of processing PLAs filled with metals such as brass, bronze, copper, stainless steel, and iron, as well as conductive PLA for low voltage applications and magnetic iron. This printer features automatic leveling calibration print plate technology and a heated print bed to prevent warping. The print bed can be set up to 80 degrees Celsius (176 degrees Fahrenheit).

    The Robo R1+ printer works with the free open-source Matter Control software, which supports file slicing prior to printing. The unit supports standalone printing from an SD card, whereas the C2 and R2 models have USB stick file transfer functionality.  The R1+ ships with a power cable, spool of filament, SD card, toolkit, quick start guide, and a one-year subscription to Autodesk Fusion 360. This printer model carries a six-month manufacturer’s warranty and lifetime support.

    Robo C2

    The C2 is Robo’s compact, mid-range 3D printer model. This Robo 3D printer has a print size of 5″ x 5″ x 6″ (127 x 127 x 152.4 mm), overall dimensions of 13″ x 18.25″ x 12.75″ (330.2x 463.55 x 323.85 mm), and weighs 20.8 pounds (9.43 kg). The C2 is capable of printing with more than 20 material types including a variety of PLAs, PET-G, flexible TPE and TPU, magnetic iron, HIPS, and PVA. The R1+ and R2 models support a wider range of materials and have larger print sizes. All of these printers are compatible with Robo and non-Robo filaments.

    The C2 prints with a layer resolution ranging from 20 up to 300 microns and has XYZ accuracy of 12.5, 12.5, and 5 microns. The quick-change 0.4 mm nozzle on this device has a print speed of up to 16 cubic millimeters per second and travel speed up to 250 mm/s. The nozzle temperature can reach 290 degrees Celsius (554 degrees Fahrenheit). The print plate on this model features automatic leveling calibration technology but does not come with a heated print bed.

    Customers interested in adding a heated print bed to prevent warping during printing will need to find aftermarket parts and connect the bed to the electrical outputs on the controller. They may also need to convert the removable plastic bed on the C2 printer to another material such as aluminum for reliable and safe performance. You might also consider the affordable and significantly larger Robo R1+ printer or the much more expensive and slightly larger R2 model.

    The C2 goes beyond the limited connectivity of the R1+ by supporting Ethernet and Wi-Fi connectivity. This printer model also has the capability to function as a personal hotspot. This model supports USB file transfers and comes with a stick pre-loaded with 3D models. The C2 is compatible with a wide variety of devices including computers running Mac OS, Linux, and Windows to tablets and smartphones. Like the higher-end R2, the C2 printer works with the free Robo mobile application and Cura preparation software.

    The Robo C2 is the most affordable printer made by the company to feature an LCD touchscreen that simplifies the control scheme and allow for onboard file slicing. The screen on this model is 3.5″, which is smaller than the 5″ screen on the more expensive R2 printer. The C2 also does not feature an onboard camera for recording print jobs in progress like the R2. The C2 comes with standard printer accessories including a power cable, spool of filament, toolkit, quick start guide, and a one-year subscription to Autodesk Fusion 360. This printer model comes with a 12-month standard warranty and lifetime support.

    Robo R2

    The R2 printer is the high-end model in Robo’s current product line. This high-performance smart 3D printer has an 8″x 8″ x 10″ (197 x 197 x 250 mm) print size and overall dimensions of 16.75″ x 23.75″ x 16.61″ (425.5 x 603.3 x 421.9 mm). This fully-featured model weighs in at 30.2 pounds (13.7 kg), making this printer considerably heavier than the R1+ and C2. Like the R1+, the R2 is capable of printing with over 30 types of materials. This model features sensors that detect when the filament is running low and automatically pauses the print job in progress. The R2 features a removable print plate and a print bed with automatic leveling calibration.

    The Robo R2 also stands out with its 5-inch LCD screen with control options. This printer model has Ethernet and Wi-Fi connectivity and functions as a personal hotspot. This printer is compatible with computers running Mac OS, Linux, or Windows as well as open-source software, the free Robo application for iOS and Android devices, and free Cura Preparation Software to ready, manage and monitor the 3D print job from a tablet or a smartphone. Like the C2, this model also supports onboard file slicing for ease of use. This model also boasts a camera to record print jobs in progress and enable users to watch the footage on a mobile device.

    Enhance the functionality of the R2 printer with a forthcoming option to add a second extruder. This add-on will allow users to print designs with two different materials or two different colors of the same material at the same time. This model is capable of printing with a layer resolution ranging from 20 to 300 microns and XYZ accuracy of 12.5, 12.5, and 5 microns. The travel speed on this advanced consumer model goes up to 250 mm/s, while this printer is capable of extruding at up to 16 cubic millimeters per second.

    The quick-change nozzle on the R2 printer has a 0.4 mm diameter and reaches temperatures up to 290 degrees Celsius (554 degrees Fahrenheit). The heated print bed can reach up to 100 degrees Celsius (212 degrees Fahrenheit). This bed helps to prevent warping and comes with a BuildTak sheet to make it easier to remove print projects.

    This Robo 3D printer supports both standalone printing from a USB stick and Wi-Fi file transfer for printing directly from the brand’s application. In addition to a power cable, spool of filament, toolkit, quick start guide, and a one-year subscription to Autodesk Fusion 360, the R2 printer also comes with a USB stick loaded with 3D models. This printer comes with a one-year warranty and lifetime support.

    Pricing

    Robo offers 3D printers priced between $500 and $1500. Consumers and institutions should determine which model provides the features they want at an acceptable price point. The Robo R1+ printer has the features that most 3D printing enthusiasts want with a $499.99 price tag. This model does not have the range of connectivity and smart features that come on the compact C2 or higher-end R2 models.

    The Robo C2 has a smaller print size than the R1+ with more connectivity options including Ethernet, Wi-Fi, and USB. This model supports onboard file slicing and features a 3.5-inch display with simple controls.  The C2 printer is currently priced at $799.99. The C2 and more expensive R2 models share a number of smart features, but the R2 has a larger print size, a larger touchscreen, and an onboard camera. The C2 does not have a heated print bed, and Robo does not sell compatible beds. This model also prints with a more restricted range of materials than the R1+ or R2.

    The most advanced 3D printer by Robo, the R2, currently sells for $1,499.99. This model is set apart by its integration of a 5-inch touchscreen, onboard camera, and heated print bed. The R1+ and R2 are both capable of printing in more than 30 materials, but Robo proposes that the R2 will soon support the use of multiple extruders. There is a $1000 price difference between the R1+ and R2 and a $700 price difference between the C2 and R2 Robo 3D printer models.

    Robo also sells 3D printer bundles with C2 or R2 printer models for educational purposes. K-12 instructors may be interested in the MyStemKits bundles with three printers, one year of curriculum support, four hours of online training, and 250 student licenses. Individual users interested in 3D printing a basic quadcopter drone should consider the Robo 3D Print Project model for $99.99. The company also sells desk clock and guitar 3D print kits in the $40 range.

    How Robo 3D Printers Compare

    FlashForge 3D Printer

    Price$349.99
    Ease of Use
    Assembly Time
    Build Quality
    Warranty

    Creality3D CR-10 Mini 3D Printer

    Price$359
    Ease of Use
    Assembly Time
    Build Quality
    Warranty

    Anycubic 3D Printer Mega

    Price$368.99
    Ease of Use
    Assembly Time
    Build Quality
    Warranty

    Pros and Cons

    PROS

    • Accessible consumer desktop-style 3D printers
    • Price range from $500 up to $1500
    • Prints with many types of materials

    CONS

    • Robo printers and materials tend to be more expensive than other brands

    Conclusion

    If you want a consumer-level desktop 3D printer with a wide range of functionality, consider one of the three Robo 3D printer models in this review. The brand’s current line makes it easy to select a printer that will fit your budget and design preferences. You may be able to find a refurbished unit of your preferred printer model for a lower price. Robo also sells accessories, materials, and kits that make it easy to get started and learn about 3D printing.

  • Canon Waterproof Camera Review – PowerShot D30

    Canon Waterproof Camera Review – PowerShot D30

    Whether you want to enter the world of underwater photography or you simply want a camera that will stand up to the water during your outdoor adventures, a good waterproof camera is a solid investment. And thanks to all the improvements in camera technology over the years, even cameras that focus mostly on being waterproof take quality photos and videos at a decent resolution.

    No matter what sort of camera you’re in the market for, it’s always a good idea to see what features a top brand like Canon has available. As you might expect, Canon offers a range of different waterproof cameras to allow you to take your love of photography with you wherever you go — even if that place happens to be 50 feet underwater. Not only are these cameras waterproof, but they also feature Canon technology that allows them to take high-quality pictures and videos in all sorts of different situations.

    One popular waterproof camera from Canon is the Canon PowerShot D30. This camera is not only a fairly capable waterproof option that’s suitable for Open Water scuba divers; it’s a flat-out good camera no matter how you slice it. However, there are a lot of competitors on the market, so you’d be wise to take a look at all the different waterproof cameras in this price range before making your decision. We’ve put together a comprehensive Canon waterproof camera review for the PowerShot D30, including a look at its features and specs, how it performs underwater and how good the camera itself is. If you’re having a hard time choosing the best waterproof camera, this review should help you out.

    Quick Navigation
    What Is the Canon PowerShot D30?
    Canon PowerShot D30 Specifications
    Pricing
    How It Compares
    Pros and Cons
    Conclusion

    What Is the Canon PowerShot D30?

    [amazon fields=”B00K47O5BY” value=”thumb” image_size=”large”]
    [amazon fields=”B00K47O5BY” value=”button”]

    The Canon PowerShot D30 is, at the time of writing, the only waterproof camera Canon has available directly from its website. As far as specs and prices go, it’s nowhere near the top-of-the-line cameras you might expect from Canon, but it’s got some great features that make it a good choice if you need something waterproof. Although it’s designed to handle depths that go beyond what you can explore with Open Water scuba certification, the PowerShot D30 is also shockproof up to 6.5 feet which makes it a great option for hiking, fishing or any other outdoor use.

    As far as the actual body and lens go, the Canon PowerShot D30 is basically a standard digital camera. If it didn’t mention its waterproof and shockproof ratings on the front of the camera, you might not even know this was a waterproof model. Unfortunately, this also means that you won’t get an insane photo and video quality with this camera. While it will give you good underwater still images and videos, especially for the price you’re paying, don’t expect the Canon PowerShot D30 to give you underwater camera quality like you see when professionals use expensive underwater cameras.

    Canon PowerShot D30 Specifications

    As far as the specifications go, the Canon PowerShot D30 is pretty much what you’d expect from a standard digital camera with a waterproof and shockproof body that makes it perfect for outdoor adventures. This camera is waterproof up to 82 feet and shockproof up to 6.5 feet, so both ratings are more than enough to handle regular outdoor use if you’re looking for a good hiking or fishing camera. However, the 82-foot waterproof rating means the Canon PowerShot D30 can go well beyond the 59 feet you can dive with Open Water scuba certification, so it should be fine for your needs unless you’re diving deeper than 82 feet.

    The camera in the Canon PowerShot D30 is a 12.1 MP camera with a 1/2.3-inch CMOS sensor. After you’ve taken a beautiful picture with the camera, you can look at it on the 3.0-inch TFT color LCD monitor. The maximum aperture is f/3.9 (W) and f/4.8 (T), so you have a decent depth of field but not great. Two different shutter speeds – 1-1/1600 sec and 15-1 sec – allow you to shoot either regular or long exposure photos. You also get tons of technology and options for controlling exposure, white balance, and shooting modes, which include color swap, underwater, snow, super slow-motion movie, and fisheye mode.

    The Canon PowerShot D30 can take images in 16:9 resolutions up to 4000 x 2248 and 4:3 resolutions up to 4000 x 3000, so the resolution will never be the primary problem when it comes to your image quality. As for videos, you can record at 24 fps in 1080p, 30 fps in 720p, and 120 fps or 240 fps depending on which super slow-motion mode you choose – 320 x 240 having the higher framerate and 640 x 480 having the lower one. You can play your videos back on the LCD monitor at 30 fps.

    The SD card, SDHC card and SDXC card support allows you to insert a memory card in your Canon PowerShot D30 and easily expand the storage. Canon doesn’t mention how much storage capacity in a memory card can be supported, but the support for a range of SD card formats means you can probably use a fairly large memory card in this camera. Although this is a generally standard feature for a modern camera, it’s nice to know you can add a significant amount of storage to the Canon PowerShot D30 and easily swap out another SD card when you need more storage out on the water.

    Pricing

    [amazon fields=”B00I58LNF0″ value=”thumb” image_size=”large”]
    [amazon fields=”B00I58LNF0″ value=”button”]

    Despite the fact that the Canon PowerShot D30 is a capable waterproof camera that can satisfy the needs of most certified scuba divers, this camera has an MSRP of just $329.99, and you can even find it for less at some retailers. While it won’t give you the most amazing performance in terms of picture quality, an 82-foot waterproof rating and a 6.5-foot shockproof rating with a 12.1 MP camera for $329 is a good value.

    The thing about the price of this camera is that you can find cheaper underwater cameras from other manufacturers which, on the surface, appear to have better specs. However, cameras are tricky because determining whether or not a camera captures quality photos and videos isn’t as simple as looking at the megapixel rating or the resolution at which it captures photos and videos. A lot of different factors go into making a good camera, and you’re always better off paying more for quality. For example, there is a $59.99 20 MP underwater camera at Walmart from a brand called Ivation that gets a 3.5-star rating. While this may look like a higher-quality camera, chances are you’re getting better quality from Canon despite the lower specs.

    As far as other high-end brands go, Olympus has a 12.0 MP camera called the Olympus Tough TG-5 that’s waterproof up to 50 feet and shockproof up to 7 feet. It’s capable of recording 4k video, but it costs $379.99, which is slightly higher than the Canon PowerShot D30. Nikon makes a 16 MP camera called the Coolpix AW130 that’s waterproof up to 100 feet and shockproof up to 7 feet with 5x optical zoom. This camera is currently for sale at Walmart for $328, but it’s only capable of recording full HD video like the Canon PowerShot D30 rather than 4k like the Olympus.

    We offer this information to show that the Canon PowerShot D30 is about as good a value as you can expect to find in a waterproof camera. You might be able to find comparable models at a similar price point or slightly better models for a little bit more money, but you won’t find anything that blows this camera out of the water – no pun intended – unless you want to spend a bit more money.

    How It Compares

    person holding black ceramic coffee mug beside black DSLR camera

    Image via unsplash.com

    There aren’t a ton of different waterproof cameras in the same price range as the Canon PowerShot D30, but for the most part, all of the models we compared it to are pretty similar in features. For the purposes of this article, we’ll be talking about how the Canon PowerShot D30 stacks up to the Olympus Tough TG-5 and the Nikon Coolpix AW130.

    As far as the cameras go, the Nikon Coolpix AW130 takes the lead with a 16 MP camera compared to 12.1 for the Canon PowerShot D30 and 12 for the Tough TG-5. All three cameras are the same when it comes to the 1/2.3-inch CMOS sensor. The Tough TG-5 gives you the ability to record 4k video at 30 fps, which beats out the PowerShot D30 and the Coolpix AW130 by a fair amount. Also, the Coolpix AW130 is capable of recording 1080p video at 30 fps while the PowerShot D30 tops out at 24 fps. Fortunately, the PowerShot D30 makes up for that with the ability to record super slow-motion video at two different framerates, something that neither of the other cameras is capable of.

    The waterproof and shockproof ratings of these three cameras vary quite a bit. The PowerShot D30 gives you an 82-foot waterproof rating and a 6.5-foot shockproof rating, while the Tough TG-5 offers a 50-foot waterproof rating and 7-foot shockproof rating. The Coolpix AW130, on the other hand, offers a 100-foot waterproof rating and 7-foot shockproof rating that beats both of the others. The 50-foot waterproof rating on the Olympus Tough TG-5 is a bit disappointing, but it’s still enough depth for most divers.

    With the prices of these three cameras being pretty similar, it’s hard to argue for or against any one particular model. Each camera has different things it excels at, and the camera you choose will ultimately depend on the specific features you’re looking for. However, it’s safe to say that the Canon PowerShot D30 stacks up nicely to the competition.

    Pros and Cons

    PROS

    • the Canon Powershot D30 has a nice waterproof and shockproof rating
    • 2.1 MP camera rating and 1/2.3-inch CMOS sensor give you good photo and video quality
    • record 1080p video and super slow-motion video at two different resolutions
    • Image resolutions of up to 4000 x 2248
    • At just $329.99, this camera won’t cost you a fortune but will still give you everything you need to start capturing photos and videos underwater

    CONS

    • Canon PowerShot D30 is only capable of recording 1080p video at 24 fps, which is a tad lower than the 30 fps standard which most cameras record at
    • The lack of 2k or 4k video recording is also a bit disappointing to see in a model in this price range, even though the framerate is already a bit low at 1080p
    • 30 fps playback means you don’t get the full benefit of your 120 fps or 240 fps super slow-motion video unless you’re playing it back on another device
    fishes underwater

    Image via unsplash.com

    Although the Canon PowerShot D30 is a good underwater camera, it has both pros and cons. Some of these may be minor problems for you while others may be huge annoyances, so this is a good tool for helping you make the right decision.

    As far as the pros go, the Canon Powershot D30 has a nice waterproof and shockproof rating. The 12.1 MP camera rating and 1/2.3-inch CMOS sensor give you good photo and video quality, and that’s reflected by the fact that you can record 1080p video and super slow-motion video at two different resolutions. Image resolutions of up to 4000 x 2248 give you the kind of quality you’d expect from a Canon camera. At just $329.99, this camera won’t cost you a fortune but will still give you everything you need to start capturing photos and videos underwater.

    There are some cons, however. For starters, the Canon PowerShot D30 is only capable of recording 1080p video at 24 fps, which is a tad lower than the 30 fps standard which most cameras record at. The lack of 2k or 4k video recording is also a bit disappointing to see in a model in this price range, even though the framerate is already a bit low at 1080p. 30 fps playback means you don’t get the full benefit of your 120 fps or 240 fps super slow-motion video unless you’re playing it back on another device.        

    All in all, the Canon PowerShot D30 has its fair share of both pros and cons. If the cons outweigh the pros for you, you might want to consider looking at another underwater camera model.

    Conclusion

    man holding digital camera

    Image via pexels.com

    Like we said before, the Canon PowerShot D30 isn’t going to give you the type of professional photo and video quality you see when scuba divers take an expensive camera underwater. However, the fact that you can record 1080p video and super slow-motion video with the Canon PowerShot D30 means you’ll get good enough quality for basic needs. Great waterproof and shockproof ratings make this a good camera for diving, fishing, hiking, or pretty much anything else you do in the great outdoors. The fact that you can get all of these features in a camera for a little more than $300 is great news if you want to start capturing underwater moments without spending a fortune on an expensive professional-quality camera.

  • Cetus 3D Printer Review – Is It Worth To Buy?

    Cetus 3D Printer Review – Is It Worth To Buy?

    monoprice maker select 3d printer

    Featured Image: Amazon

    What began as a crowdfunded Kickstarter project has now become a fully-fledged product that is available for retail purchase. When the Cetus 3D Printer was first launched on Kickstarter, the device was offered from Cetus3D, a subsidiary of Beijing Tiertime Technology LTD., for only $199. Now that the project has been funded, and the Cetus 3D is available to the general public, we’re here to see if the Cetus 3D can actually “Make It Happen”, as its tagline suggests. With 589 backers supporting the project with over $169,103, it seems that this 3D printer is a success. Let’s dive deeper into the features and benefits of the Cetus 3D Prints, as well as its advantages and disadvantages.

    Quick Navigation
    What is the Cetus 3D?
    Product Specfications
    Pricing
    How It Compares
    Cetus 3D Printer
    MonoPrice Maker Select Plus
    Original Prusa I3 MK2S Kit
    How We Reviewed
    Buyer’s Guide
    Conclusion

    What is the Cetus 3D?

    tiertime cetus printer

    Image via Amazon

    A 3D printer is a machine that is capable of additive manufacturing by way of creating three-dimensional objects from digital files. The additive creation process describes the creation of an object through building an object upward with successive layers until the object is complete. On the other hand, subtractive manufacturing describes the process of creating an object by cutting out or hollowing out pieces from a block of material. In this way, 3D printing is a more efficient way of manufacturing while retaining the ability to create complex three-dimensional objects.


    Using a 3D modeling software on your computer or a 3D scanner, a digital file is where the three dimensional printing begins. 3D scanners can range from industrial grade to homemade scanners that can be built for around $30, and 3D modeling software is similar in nature, with both costly professional grade programs and free open source programs available. No matter which route you take to obtain your model, you will need to prepare it for printing.


    The process of preparing your 3D model for printing is called slicing, which divides the model into a multitude of layers so that a 3D printer can build it from the ground up using additive manufacturing. This is typically done with a separate slicing software, and it should be noted that some printers might require proprietary slicing software. Once the model is sliced, you are ready to begin printing, which can be done over SD, Wi-Fi, or USB connection. When the printer receives the 3D model, it will begin printing your object layer by layer.

    Product Specfications

    3d printer with printed dragon

    Image via Amazon

    The Cetus 3D Printer is a minimalist 3D printer that is constructed from an aluminum body that can be divided into six different modules: the extruder; the build platform; the main board; and the X,Y, and Z axes. Although the machine is small and only weighs just over three kilograms, its build volume is massive for its size. The volume of the machine itself is 260x260x280mm, and the build volume is 180x170x180mm. This means that you are able to print objects that are nearly as big as the machine itself.


    Additionally, the rails are self-lubricated and maintenance free. The machine is quiet, and offers high precision without the noise that accompanies other printers. Three nozzles are also offered in different sizes for detail. A 0.2mm, 0.4mm, and 0.6mm nozzle are available, and each has its own preset profile for a hassle-free print.
    The 3mm aluminum build plate guarantees that your print surface is flat, as it is fixed directly to the linear guide, giving a flat surface that runs parallel to the X-axis. Furthermore, each Cetus 3D Printer comes from the factory with a pre-calibrated Y-axis to allow users to be able to begin printing right out of the box.

    The Cetus 3D Printer has a dedicated modeling software that utilizes a user-friendly interface that is supported on Mac, Windows, and even iOS, and a big advantage that the Cetus 3D Printer offers is the ability to work with third-party slicing software, such as Cura, Slic3r, and Simplify3D. This gives users who are more familiar with 3D printing the ability to achieve the best quality print from the Cetus 3D Printer. For particularly advanced users, the Cetus 3D Printer is Gcode compatible and can be modded in order to perform laser engravings and other functions that operate by Computer Numerical Control.

    Pricing

    The Cetus 3D Printer can be purchased for $399 from the Cetus3D website.

    How It Compares

    Cetus 3D Printer

    [amazon fields=”B07K3ZWX5X” value=”thumb” image_size=”large” image_align=”center”]

     

    [amazon fields=”B07K3ZWX5X” value=”button”]

    Build Volume

    180x170x180mm

    Filament Compatibility

    1.75mm

    Material

    PLA/ABS/PETG

    Warranty

    3 Months

    PROS

    • The Cetus 3D Printer is easy to use, and is a great introductory 3D printer with the power to satisfy advanced users.
    • This machine has a high build quality with a minimalist design.
    • The Cetus 3D Printer has a spacious build volume that is nearly as large as the machine itself.
    • For an affordable cost, you get a very capable 3D printer with a wide range of compatibility.
    • The fixed bed has no need to be leveled.
    • It is equipped with Wi-Fi connectivity.

    CONS

    • Some users have noted that the fan is noisy.
    • The printer uses proprietary nozzles.
    • Monoprice Maker Select Plus

    MonoPrice Maker Select Plus

    [amazon fields=”B01JBEF3T8″ value=”thumb” image_size=”large” image_align=”center”]

     

    [amazon fields=”B01JBEF3T8″ value=”button”]

    Build Volume

    180x170x180mm

    Filament Compatibility

    1.75mm

    Material

    ABS, PLA, XT Copolyester, PET, TPU, TPC, FPE, PVA, HIPS, Jelly, Foam, Felty

    Warranty

    30 days

    PROS

    • It offers a large build volume.
    • The Monoprice Maker Select Plus is equipped with a touch screen with an intuitive interface.
    • A wide variety of materials can be used with the printer.
    • The Monoprice Maker Select Plus is an affordable option for those who are serious about entering the 3D printing hobby.
    • It is a high quality, reliable machine.

    CONS

    • The maximum resolution of the Monoprice Maker Select Plus is average at best.
    • There is no auto-leveling feature

    Original Prusa I3 MK2S Kit

    [amazon fields=”B071YLPJVN” value=”thumb” image_size=”large” image_align=”center”]

     

    [amazon fields=”B071YLPJVN” value=”button”]

    Build Volume

    250x210x200mm

    Filament Compatibility

    1.75mm

    Material

    Any thermoplastic including Nylon and Polycarbonate

    Warranty

    1 Year

    PROS

    • The kit comes with its own tools, so there’s no need to own any prior to purchase.
    • The printer is easy to use, even for beginning printers.
    • While the assembly is a challenge, it can help those who are new to the hobby get to know their new machine.
    • The Original Prusa i3 MK2S Kit is compatible with a variety of different material filaments.

    CONS

    • It’s more expensive than other brands, and it is not pre-assembled.

    How We Reviewed

    original prusa printer

    Image via Amazon

    We believe that it is important to bring you accurate and honest information in our reviews, and as such, we like our readers to understand the review process. First, we search for all of the product data available for the product that is under review, and then we find some of the item’s closest competitors and research them in a similar fashion. We also take into account user feedback from people who already own each product. Once all of the data is compiled, we are able to offer factual information while also highlighting the opinions of the product’s target audience.

    Buyer’s Guide

    If you are interested in diving into the hobby of 3D printing, following these tips in our Buyer’s Guide can help you to choose the correct 3D printer to get you started. Whether you decide to begin with one of the printers that are found in this article or another 3D printer, following these helpful tips can make the purchase of your new investment hassle-free and painless.

    Set a budget for yourself, and don’t deviate from the limit that you set for yourself. If you decide to continue your research for a 3D printer outside of those models that have been covered in this article, you can begin to filter your options by maximum price. This can narrow your choices down and make the process of finding the right 3D printer for you that much simpler.


    Familiarize yourself with common features that appear in the models that fall within your price range. You can eliminate models that have features you believe you will not need or will not use during your time with the machine. By eliminating models with features that will go unused, you can once again narrow the choices for your perfect printer. This may also help to lower the cost of your machine. By that same token, make not of models that have features that you would enjoy.

    Review feedback from customers who have already purchased the 3D printer. Typically, you can find these reviews on the manufacturer’s websites. It should be noted that analyzing both positive and negative reviews is important, as it will help you to find a balanced take on how you might feel about the printer if you decide to purchase it. Once again, reviewing this type of feedback can help to thin out competitors even more in your search, because an overall negative customer rating is generally a red flag indicating that you would be better off looking elsewhere.

    Conclusion

    After our thorough review, we believe the Cetus 3D Printer is a perfectly suitable 3D printer for those who are first entering the 3D printing and plastics hobby, and for veterans alike. While some users found issues with the proprietary Cetus nozzles, and others mentioned that the cooling fan is loud, these qualms shouldn’t necessarily disqualify the Cetus 3D Printer from consideration, because this little machine has its strengths. The biggest advantage to the Cetus 3D Printer is the build volume that the device offers. For its reasonable price, the Cetus 3D Printer gives you the ability to print fairly large objects. Additionally, the Cetus is incredibly easy to use. Many users noted how quickly they were able to begin creating while their friends were frustrated with the more complicated machines that they purchased. The Cetus’ minimalist design is truly the heart of this 3D printer. It is sleek yet efficient, and it has a no-nonsense approach to 3D printing.


    That’s where you come in. Another of the Cetus 3D Printer’s big advantages is its flexibility when it comes to compatible software. If you are already familiar with slicing programs such as Cura, Slic3r, and Simplify3D, you can continue working with those programs and still use the Cetus 3D Printer. Additionally, the printer is fully calibrated from the factory, and the build platform is flat and requires no leveling, ensuring a perfect print every time. The linear rails are quiet with the frame constructions being generally solid in nature. The Cetus 3D printer also offers an extendable design for more advanced users to tinker with, and the Wi-Fi connectivity makes sending files to the printer easy to do. Tiertime, the company of which Cetus3D is a subsidiary, has been steeped in the 3D Printing industry for 15 years. This brings experience to the table, and recognition of talent.


    Speaking of recognition of talent, it bears repeating that the Cetus 3D Printer was a successful Kickstarter project. In the sea of projects vying for crowd funding, the Cetus 3D Printer was able to source the funds needed to make their printer a complete package while offering backers the printer for an unreal discount of $199. Supporters for projects such as the Cetus 3D Printer are usually people who have their finger on the pulse of newly available technology. That simple fact may be enough for some to make the Cetus printer a cut above some of its competitors who haven’t had seal of consumer approval in their pre-retail stage.


    When all of the dust has settled, the positives of the Cetus 3D Printer far outweigh the negatives, and we would be confident in recommending this 3D printer to anyone who is interested in purchasing one, regardless of experience. From its ready-to-use nature to its incredible build volume and ability to be customized for other CNC functions, this printer nearly does it all. The Cetus 3D Printer is simply one of the best available at its price point.

  • Fuji Waterproof Camera Review

    Fuji Waterproof Camera Review

    Fuji Waterproof Camera Review

    The next time you’re at the beach, leave your expensive smartphone behind. If you’re trying to take pictures at the pool or on the lake but are worried about water damage to your phone or camera, try a rugged Fuji waterproof camera. This complete review will give you all the information you need to choose the best waterproof camera. You’ll see a head-to-head comparison of popular waterproof cameras and learn all the important features to look for in a high-quality waterproof camera. Whether you are an avid photographer or just want to take a few selfies on your vacation, the popular Fujifilm FinePix XP80 camera is an excellent choice.

    Quick Navigation
    What Is the Best Fuji Waterproof Camera?
    Professional or Amateur Camera
    Camera Controls
    Portable Design
    Wi-Fi Functions
    Zoom
    LCD Screen
    Shooting Modes
    Specifications of the Fujifilm FinePix XP80
    Pricing
    How It Compares
    Fujifilm FinePix XP80
    Olympus TG-5
    SeaLife DC2000 HD
    Pros and Cons of the Fujifilm FinePix XP80
    Conclusion

    [amazon box=”B00S4KXH3K, B071RSJGXZ, B01MYZG3PO” template=”table”]

    What Is the Best Fuji Waterproof Camera?

    The Fujifilm FinePix XP80 is a highly rated and durable camera. It comes with an extremely tough case, reasonable picture quality and a very affordable price tag. It’s hard to find a tough camera that’s a better bargain. To understand why this Fujifilm camera is so popular, and to determine whether it’s the right choice for you, take a look at some of the most important features to consider when buying waterproof cameras.

    [amazon box=”B00S4KXH3K”]

    Professional or Amateur Camera

    One quick scan of any camera website or department store, and you’ll realize there’s an incredibly wide range of prices for cameras. Obviously, the features and picture quality will vary with each one, as well.

    Basic, inexpensive cameras are often called point-and-shoots. These inexpensive cameras may have a zoom function, but otherwise they offer little additional manual controls. They don’t come with interchangeable lenses, manual focus options or a large sensor. The FinePix XP80 is a point-and-shoot camera. While it takes reasonable pictures for your own photo albums and social media, it isn’t considered a professional-quality camera.

    More expensive cameras, like SLRs and DSLRs, have large sensors and manually adjusted lenses that are interchangeable. These cameras are far more expensive and have a steep learning curve, but they can take truly professional-quality pictures.

    Camera Controls

    Do you want a camera you can manually adjust to get the perfect shot, or do you want an automatic option that instantly takes great, focused pictures? Some cameras come with loads of controls, color and flash options and video capabilities. Others are easy-to-use cameras, with very few settings or controls. Consider how much time you take setting up a shot, and whether you want to be in control or take stress-free photos with slightly lower image quality and less customization.

    Other camera controls can be important, too. Many cameras have interval timers. This allows you to take photos at certain intervals, such as every five minutes or 30 seconds. This lets you take great pictures of flowers, sunsets or other unique settings. Most digital cameras allow video recording, but not of them all have this feature. Consider the resolution, microphone and editing capabilities of each camera if you are interested in recording excellent videos.

    Portable Design

    [amazon fields=”B00S4KXH3K” value=”thumb” image_size=”large”]

    Do you want a giant camera weighing you down, or a small, pocket-sized one? Smaller cameras, like the FinePix XP80, are better suited for travel. While they don’t offer the image quality of a professional camera, they are far more durable and easy to pack in a backpack, suitcase or carry-on bag. Of course, you’ll sacrifice overall image quality for a portable design, so smaller point-and-shoot cameras aren’t the best option for every situation.

    Wi-Fi Functions

    Some cameras are equipped with Wi-Fi functionality. There are several great reasons to choose a camera with this feature. First, you’ll never have to worry about setting a timer again. For great family photos, simply set up your camera and connect to your smartphone. You’ll be able to use your device to take photos wirelessly. You can even adjust the zoom and record videos through your phone.

    With cameras such as the FinePix XP80, you can also upload photos to your smartphone instantly. You won’t have to worry about the storage capacity of these cameras, as you can use your entire phone’s storage, as well. Or, your phone can automatically upload the photos to a cloud storage service, giving you access to far more storage space than you’ll ever need for high-quality photos and videos.

    Zoom

    Most point-and-shoot and professional cameras have zoom functions, but not all are created equal. Zoom features are usually classified by their magnification power. There is a wide range of magnification power available, so consider how far you’ll want to zoom. As you zoom in, the image quality may suffer. If you are looking for high-quality, long-range photos, consider a professional camera with a larger lens specifically designed for higher magnification levels. Otherwise, you’ll take the clearest photos if you don’t use the zoom function.

    LCD Screen

    Do you want to see the image you are going to take? Do you need to make sure the photo turned out the way you wanted? You’ll want an LCD display for both of these purposes. A high-quality LCD display makes it easy to take the perfect photo, easily navigate menus and look at older pictures.

    Most point-and-shoot cameras come with an LCD display. However, some have larger displays than others, and the resolutions of the displays aren’t always the same. Consider choosing a large, high-resolution LCD display if you want more convenience when taking pictures and reviewing old photos. However, a larger screen will dramatically decrease the battery life of your camera. Some cameras only last a few hours if you are using the LCD display. For added convenience, consider choosing a camera that has an LCD display and a viewfinder.

    Shooting Modes

    If you have a point-and-shoot camera, you may miss the ability to manually adjust it. Depending on the situation, you may want to change the focus or use other features.

    While a point-and-shoot camera lacks some of these basic capabilities, most offer a variety of shooting modes. Each of these modes is preset to provide the best camera settings for specific areas. The FinePix XP80, for example, has a wide variety of modes. Choose among night, snow, beach, portrait, action or many other options to take the best pictures in each location. Not all point-and-shoot cameras come with this many shooting modes, so consider this feature if you plan to use your camera in a variety of places. This is particularly important for a well-rounded outdoor camera like the FinePix XP80.

    Specifications of the Fujifilm FinePix XP80

    ​

    • $169.00
    • 16.4 million pixels
    • 2.7-inch LCD monitor
    • Micro HDMI output
    • Waterproof up to 15 meters or 50 feet
    • 5x optical zoom
    • 6.3 ounces
    • 3.8 stars from customers

    The Fujifilm FinePix XP80 is an excellent camera for almost any outdoor excursion. Pick up this durable camera for a day at the beach, a hike through the mountains or a trip to any other adventurous location. It’s not only waterproof for 15 meters, but it’s also shockproof. It can handle a drop from up to 5.8 feet.

    When outside the water, it takes pictures of reasonable color and sharpness. Underwater photos have lower image quality, so this camera isn’t the best choice if you want ultra-sharp pictures. It also can’t withstand the same depth of water as other, more expensive waterproof cameras. Still, it’s a very affordable underwater camera, particularly when used as a backup option. The plastic case is stylish and ergonomic, giving you a lightweight and practical camera for all-weather photos.

    Pricing

    When it comes to cameras, you usually get what you pay for. If you want crystal-clear pictures with lots of vivid color, expect to pay for a high-end camera. DSLR cameras, in particular, can cost as much as $3,000, without any additional lenses. Inexpensive point-and-shoot cameras are usually at least $100. The waterproof cameras on this list cost between $169.00 and $699.00. Determine the image quality you are looking for, and find the best camera in your price range. Some premium cameras also have additional features and higher waterproof ratings.

    How It Compares

    [amazon link=”B00S4KXH3K” title=”Fujifilm FinePix XP80″]

    [amazon box=”B00S4KXH3K”]

    Price

    ???

    Ease of Use

    Build Quality

    Warranty

    [amazon link=”B071RSJGXZ” title=”Olympus TG-5″]

    [amazon box=”B071RSJGXZ”]

    Price

    ???

    Ease of Use

    Build Quality

    Warranty

    With its high-speed sensor, the 12-megapixel Olympus TG-5 is an excellent mid-range camera. It’s waterproof up to 50 feet and drop-proof up to seven feet. It comes with the same durable features of the FinePix XP80, but it also takes clearer images and offers high-definition video recording. It captures 20 frames per second, so it’s designed to shoot action shots without blurry lines. The large sensor allows it to take clearer photos in low-light situations, so you can use this camera underwater. Customers love this durable and convenient camera, particularly for underwater photos. However, it’s considerably more expensive than the FinePix XP80, so it isn’t appropriate for budget shoppers.

    [amazon link=”B01MYZG3PO” title=”SeaLife DC2000 HD”]

    [amazon box=”B01MYZG3PO”]

    Price

    ???

    Ease of Use

    Build Quality

    Warranty

    With an impressive 20 megapixels and a speed of 60 frames per second, the SeaLife DC2000 HD offers some of the best specifications among waterproof cameras. It’s waterproof up to 60 feet, and it can handle drops of up to five feet. It has the largest sensor of these underwater cameras, along with plenty of functions and impressive features. Try taking full high-definition videos, or photos with full manual controls. The included battery lasts over two hours with continuous use, so you’ll be able to take pictures throughout your dive or day at the beach. If you’re diving in particularly dark areas, consider purchasing a light or flash bulb attachment for even better image quality. However, this camera is far more expensive than the other options. Many customers also feel the pictures aren’t any clearer than those taken by the Olympus TG-5.

    Pros and Cons of the Fujifilm FinePix XP80

    While it isn’t the most professional-grade camera on the market, there are many great reasons to choose this Fuji waterproof camera. Take a look at the pros and cons of the Fujifilm FinePix XP80, and consider whether it’s the right camera for you.

    PROS

    • Affordable Price
    • Excellent quality photos
    • Durable and sleek design
    • Dusproof
    • Designed to work well underwater or on land

    CONS

    • Compared to more expensive cameras, the FinePix XP80 has average image quality and less vivid colors
    • Many customers feel the sensor doesn’t work as well as other waterproof cameras’ sensors in low-light situations.
    • Other Cameras can take photos from even deeper underwater.

    Conclusion

    A rugged and convenient underwater camera, the Fujifilm FinePix XP80 receives 4 out of 5 stars. It’s an excellent option that balances cost and durability. Take this camera on your next adventure, and see how well it stands up to water, drops, cold temperatures and dust. Take reasonable pictures and video, and remember your big adventure for a lifetime. However, consider each waterproof camera option carefully. While this camera doesn’t offer the best quality photos or the most durable design, it’s one of the most affordable waterproof cameras on the market that still retains some image excellence.

    So grab your camera and backpack and get ready for your next adventure. Choose the Fuji waterproof camera, and wherever you go, you’ll enjoy excellent pictures from this durable, affordable camera.